Generator installation in Smithville fits a town where about 76 percent of housing units are single-family detached homes, and each of those homes has its own panel and meter to tie a generator into. When the grid drops, a standby generator starts on its own and carries the circuits you choose. Veteran Electric KC is a veteran-owned and operated, licensed electrician founded in 2025, and we handle the electrical side of the job from the first walk-through to the final inspection. Every project starts with a free estimate, and you get the price in writing before work begins.
A permanent generator is different from a portable one. It is wired into your panel through a transfer switch, connected to your gas supply, and set on a pad outside, so nothing needs to be dragged out or fueled by hand. We also install manual transfer switches for homeowners who want to run a portable unit safely through the panel. Our job is to size the system to your loads, pull the permit, book the inspection and leave you with a unit you understand. We are licensed and insured in Missouri.
Here is what a full installation covers on the electrical and coordination side.
People often ask what size generator fits a home on 100 amp service. There is no single answer, because size follows the loads you want running, not the service rating alone. A whole house generator in Smithville has to cover the air conditioner, furnace blower, sump pump and refrigerator you rely on, while a smaller unit can serve selected circuits only. We total those loads at the walk-through and recommend a size from the numbers. We install 100, 200 and 400 amp services, and we recommend 200 amp for most homes.
Yes, a generator needs a transfer switch. It is the device that connects the generator to your home’s wiring and isolates the house from the utility lines while the generator runs, which protects line crews and your equipment. An automatic switch handles the change on its own. A manual transfer switch, often built as an interlock kit, lets you power the panel from a portable generator without extension cords. Standby generator installation in Smithville usually pairs with the automatic type, and either option is code-driven work that should be permitted and inspected.


We review your panel, the gas meter location and the outdoor spot for the unit, then total the loads you want backed up.

You get a free estimate with the price in writing, and once you approve it we pull the permit.

We set the pad, mount the unit, run conduit and wiring to the transfer switch, and coordinate the gas connection with a licensed plumber.

After the inspection is booked and passed, we start the unit, test it through a simulated outage and review the controls with you.
Smithville is largely a town of owners. About 84 percent of occupied homes are owner occupied, so the person signing the estimate is usually the person who lives with the result. Heating shapes the sizing conversation too. About 55 percent of occupied homes heat with electricity as their main fuel, about 40 percent heat with utility gas, and about 3 percent use bottled or tank propane. Electric heat adds load a generator has to carry, while gas and propane homes have a fuel supply to connect to.
Older and newer homes call for different attention. About 12 percent of Smithville’s 4,176 housing units (506 homes) were built before 1960, and panels in those houses may need a closer look before a generator is tied in. Another 702 homes there were built in 2010 or later, about 17 percent of the housing stock. Home generator installation in Smithville also follows local rules: the town enforces the 2018 International Code Council codes and the 2017 National Electrical Code, and its guidelines require wiring to be inspected before it is covered.
Homeowners in neighboring communities can read the same service written for their own town, and our Kansas City page covers the wider metro.
For the full picture, see our metro wide page or the Smithville town page.
Here are the other residential electrical services we offer homeowners in Smithville.
Run a business or manage a building in Smithville? These pages cover our commercial work there.
We handle both. We pull the permit and book the inspection as part of every generator job, so you do not have to chase the paperwork. Smithville enforces the 2018 International Code Council codes and the 2017 National Electrical Code, and its guidelines require wiring to be inspected before it is covered.
Size follows the loads you want running, not the service rating alone, so a home on 100 amp service is sized the same way as any other. We total your cooling, heating, sump pump and kitchen loads, then recommend a unit. About 55 percent of occupied homes in Smithville heat with electricity, so heating load is often a big part of the answer.
Yes. The transfer switch connects the generator to your home’s wiring and keeps it separate from the utility lines while the unit runs. Standby units use an automatic switch, and portable generators can use a manual switch or interlock kit. Because Smithville guidelines require wiring to be inspected before it is covered, we schedule the switch wiring for inspection with the permit.
Standby units typically burn natural gas or propane, so there is no gasoline to haul and pour. About 40 percent of Smithville households heat with utility gas and about 3 percent with bottled or tank propane, so the fuel question depends on your house. A licensed gas plumber makes the gas connection, and we coordinate it with our electrical work.
Yes. Veteran Electric KC is a veteran-owned and operated electrician, licensed and insured in Missouri. We install standby and whole-home generators and manual transfer switches, with a free estimate and the price in writing before work begins. Call (816) 317-0061 or visit our office at 1520 Clay St #210, North Kansas City.